21 2 3 4 5 6 this is a thin, low-profile 2.0mm (.079") pitch connector 7.5mm (.295") in height after mounting and 4.5mm (.177") in width. it is designed to meet the demand for high-density connection of internal wires to printed circuit boards. it is compact, highly reliable and low in cost. features ?reliable contact the contact has long dimples near the center to ensure a good connection at all times, even under conditions of vibration and mechanical abuse, and when used with low voltage and low current circuits. ?easy and effective crimping although the contact is compact, it has a long wire strip holding length of 2.6 +/- 0.4mm (.102" +/-.016"). this long length simplifies automatic crimping and the crimping of shielded wires. ?fully shrouded header the fully shrouded header has walls on all four sides to prevent improper connection to the mating housing and to prevent the instruction of flux and other contaminants. ?high solderable square post the square post is copper-undercoated and tin/lead-plated for superior solderability and for whisker prevention. ?printed circuit board retention mechanism the solder side of the header has a retention mechanism that prevents it from floating during soldering. as a result, the header can be positioned accurately. ?compatible with the kr insulation displacement connector the same shrouded header can be used for either ph crimp- style connector or kr insulation displacement connector. this allows both types of connector to be used interchangeably without replacing the header. ?surface mount model (smt) this connector is also available in a surface mount configuration. its housing is made of heat resistant resin so that it is not adversely affected during reflow soldering. because of its tiny size and ability to be surface mounted, this connector meets the demand for high-density mounting of components inside electronic products. specifications current rating: 2a ac, dc (awg #24) voltage rating: 100v ac, dc temperature range: - 25 ? c to + 85 ? c (including temperature rise in applying electrical current) contact resistance: initial value/10m ? max. after environmental testing/20m ? max. insulation resistance: 1,000m ? min. withstanding voltage: 800v ac/minute applicable wire: awg #32 to #24 applicable pc board thickness: 0.8 to 1.6mm(.031" to .063") * contact jst for details standards 0 recognized e60389 1 certified lr20812 2 r75087 ph connector disconnectable crimp style connectors 2.0mm (.079") pitch crimp emboss tape
22 ph connector note: 1. when using awg#32 or #30 wires, reflow-treated headers (low insertion force type, model no. b#b-ph-kl or s#b-ph-kl) are recommendable. note: 2. contact jst for gold-plated contacts. contact 1.0 (.039) 2.08 (.082) 1.5 (.059) 5.7(.224) 2.85(.112) 2.05(.081) model no. applicable wire mm 2 awg # insulation o.d. mm(in.) q'ty / reel material and finish sph-002t-p0.5s sph-004t-p0.5s 0.05 to 0.22 0.032 to 0.08 30 to 24 32 to 28 0.9 to 1.5(.035 to .059) 0.5 to 0.9(.020 to .035) phosphor bronze, tin-plated 8,000 10,000 housing 0.6(.024) a b 6.35(.250) 1.9 (.075) 2.0 (.079) 4.5(.177) 0.5 (.020) circuit no.1 cir- cuits model no. dimensions mm(in.) ab q ty / box material and finish 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 phr- 2 phr- 3 phr- 4 phr- 5 phr- 6 phr- 7 phr- 8 phr- 9 phr-10 phr-11 phr-12 phr-13 phr-14 phr-15 phr-16 2.0( .079) 4.0( .157) 6.0( .236) 8.0( .315) 10.0( .394) 12.0( .472) 14.0( .551) 16.0( .630) 18.0( .709) 20.0( .787) 22.0( .866) 24.0( .945) 26.0(1.024) 28.0(1.102) 30.0(1.181) 5.8( .228) 7.8( .307) 9.8( .386) 11.8( .465) 13.8( .543) 15.8( .622) 17.8( .701) 19.8( .780) 21.8( .858) 23.8( .937) 25.8(1.016) 27.8(1.094) 29.8(1.173) 31.8(1.252) 33.8(1.331) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 nylon 66, ul94v-0, natural (white) as the color identification, the following alphabet shall be put in the underlined part. for availability, delivery and minimum order quantity, contact jst. ex. phr-2-oo - (blank)?atural (white) bk?lack r?ed tr?omato red bl?lue y?ellow l?emon yellow m?reen d?range n?rown p?urple pk?ink h?ray le?ight blue fy?ivid yellow
23 b a 1.95 (.077) 4.5(.177) 1.7(.067) 6.0(.236) 3.4 (.134) 0.5 (.020) circuit no.1 (.134) 3.4 b a 1.95 (.077) 2.0 (.079) 0.5 (.020) 4.8(.189) 1.7(.067) 6.25(.246) 6.0(.236) 1.6 (.063) circuit no.1 b 6.0(.236) (.134) a 1.95 (.077) 2.0 (.079) 0.5 (.020) 3.4 4.5(.177) 1.7(.067) circuit no.1 through-hole type shrouded header top entry type side entry type top entry type side entry type cir- cuits model no. dimensions mm(in.) a b q'ty / box material and finish 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2.0( .079) 4.0( .157) 6.0( .236) 8.0( .315) 10.0( .394) 12.0( .472) 14.0( .551) 16.0( .630) 18.0( .709) 20.0( .787) 22.0( .866) 24.0( .945) 26.0(1.024) 28.0(1.102) 30.0(1.181) 5.9( .232) 7.9( .311) 9.9( .390) 11.9( .469) 13.9( .547) 15.9( .626) 17.9( .705) 19.9( .783) 21.9( .862) 23.9( .941) 25.9(1.020) 27.9(1.098) 29.9(1.177) 31.9(1.256) 33.9(1.335) 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 250 250 250 250 1,000 1,000 500 500 500 500 250 250 250 250 250 250 250 200 200 post: brass, copper-undercoated, tin/lead-plated wafer: nylon 66, ul94v-0, natural (white) s 2b-ph-k-s s 3b-ph-k-s s 4b-ph-k-s s 5b-ph-k-s s 6b-ph-k-s s 7b-ph-k-s s 8b-ph-k-s s 9b-ph-k-s s10b-ph-k-s s11b-ph-k-s s12b-ph-k-s s13b-ph-k-s s14b-ph-k-s s15b-ph-k-s s16b-ph-k-s b 2b-ph-k-s b 3b-ph-k-s b 4b-ph-k-s b 5b-ph-k-s b 6b-ph-k-s b 7b-ph-k-s b 8b-ph-k-s b 9b-ph-k-s b10b-ph-k-s b11b-ph-k-s b12b-ph-k-s b13b-ph-k-s b14b-ph-k-s b15b-ph-k-s b16b-ph-k-s the shrouded headers are interchangeable with those of the kr, krd and cr insulation displacement connectors. top entry type side entry type (2 circuits) (3 circuits or more) ph connector as the color identification, the following alphabet shall be put in the underlined part. for availability, delivery and minimum order quantity, contact jst. ex. b2b-ph-k-oo - s?atural (white) bk?lack r?ed tr?omato red e?lue y?ellow l?emon yellow m?reen d?range n?rown p?urple pk?ink h?ray le?ight blue fy?ivid yellow (blank)?vory
24 ph connector top entry type side entry type top entry type side entry type cir- cuits model no. dimensions mm(in.) ab q'ty / box material and finish 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 b 2b-ph-kl b 3b-ph-kl b 4b-ph-kl b 5b-ph-kl b 6b-ph-kl b 7b-ph-kl b 8b-ph-kl b 9b-ph-kl b10b-ph-kl b11b-ph-kl b12b-ph-kl b13b-ph-kl b14b-ph-kl b15b-ph-kl s 2b-ph-kl s 3b-ph-kl s 4b-ph-kl s 5b-ph-kl s 6b-ph-kl s 7b-ph-kl s 8b-ph-kl s 9b-ph-kl s10b-ph-kl s11b-ph-kl s12b-ph-kl s13b-ph-kl s14b-ph-kl s15b-ph-kl s16b-ph-kl 2.0( .079) 4.0( .157) 6.0( .236) 8.0( .315) 10.0( .394) 12.0( .472) 14.0( .551) 16.0( .630) 18.0( .709) 20.0( .787) 22.0( .866) 24.0( .945) 26.0(1.024) 28.0(1.102) 30.0(1.181) 5.9( .232) 7.9( .311) 9.9( .390) 11.9( .469) 13.9( .547) 15.9( .626) 17.9( .705) 19.9( .783) 21.9( .862) 23.9( .941) 25.9(1.020) 27.9(1.098) 29.9(1.177) 31.9(1.256) 33.9(1.335) 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 250 250 250 1,000 1,000 500 500 500 500 250 250 250 250 250 250 250 200 200 post: phosphor bronze, copper-undercoated, tin/lead-plated (reflow-treated) wafer: nylon 66, ul94v-0, gray b a 1.95 (.077) 4.5(.177) 1.7(.067) 6.0(.236) 3.4 (.134) 0.5 (.020) circuit no.1 (.134) 3.4 b a 1.95 (.077) 2.0 (.079) 0.5 (.020) 4.8(.189) 1.7(.067) 6.25(.246) 6.0(.236) 1.6 (.063) circuit no.1 b 6.0(.236) (.134) a 1.95 (.077) 2.0 (.079) 0.5 (.020) 3.4 4.5(.177) 1.7(.067) circuit no.1 top entry type side entry type (2 circuits) (3 circuits or more) through-hole type shrouded header 2.0 0.05 (.079 .002) 1.9 min. (.075) 0.7 +0.1 (.028 + .004 )dia. 0 2.8 min. 0 4.5 (.177) 8.0(.315) 6.0(.236) 2.0 0.05 (.079 .002) 1.9 (.075) 0.7 + 0.1 (.028 + .004 )dia. 0 0 6.25 min. min. 7.6(.299) 9.6(.378) 4.8(.189) 6.25 (.246) (.110) (.246) through-hole type pc board layout (viewed from soldering side) and assembly layout note: 1. tolerances are non-cumulative: 0.05mm( .002") for all centers. 2. hole dimensions differ according to the kind of printed circuit board and piercing method. if printed circuit boards made o f hard material such as fr-4 are used, the hole dimensions should be larger. the hole dimensions shown above are reference values. contact jst for details. top entry type side entry type as the color identification, the following alphabet shall be put in the underlined part. for availability, delivery and minimum order quantity, contact jst. ex. b2b-ph-kl-oo - (blank)?ray r?ed e?lue s?atural (white)
25 smt type shrouded header the shrouded headers are interchangeable with those of the kr, krd and cr insulation displacement connectors. ?mt type shrouded headers are not tu v approved. b a 2.975 (.117) 2.0(.079) 5.0 (.197) 2.0 (.079) 1.9(.075) 6.6(.260) 2.2 [ ] (.087) 1.4 (.055) circuit no.1 b a 2.95 (.116) 2.0 (.079) 2.4(.094) 5.5(.217) 6.0(.236) (.063) 1.6 2.6 (.102) [ ] sm3 type side entry type top entry type (with solder tabs) cir- cuits model no. dimensions mm(in.) top entry type side entry type top entry type side entry type a b q'ty / reel material and finish 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 b 2b-ph-sm3-tb b 3b-ph-sm3-tb b 4b-ph-sm3-tb b 5b-ph-sm3-tb b 6b-ph-sm3-tb b 7b-ph-sm3-tb b 8b-ph-sm3-tb b 9b-ph-sm3-tb b10b-ph-sm3-tb b11b-ph-sm3-tb b12b-ph-sm3-tb b13b-ph-sm3-tb b14b-ph-sm3-tb b15b-ph-sm3-tb b16b-ph-sm3-tb s 2b-ph-sm3-tb s 3b-ph-sm3-tb s 4b-ph-sm3-tb s 5b-ph-sm3-tb s 6b-ph-sm3-tb s 7b-ph-sm3-tb s 8b-ph-sm3-tb s 9b-ph-sm3-tb s10b-ph-sm3-tb s12b-ph-sm3-tb s13b-ph-sm3-tb s14b-ph-sm3-tb s15b-ph-sm3-tb 2.0( .079) 4.0( .157) 6.0( .236) 8.0( .315) 10.0( .394) 12.0( .472) 14.0( .551) 16.0( .630) 18.0( .709) 20.0( .787) 22.0( .866) 24.0( .945) 26.0(1.024) 28.0(1.102) 30.0(1.181) 7.9( .311) 9.9( .390) 11.9( .469) 13.9( .547) 15.9( .626) 17.9( .705) 19.9( .783) 21.9( .862) 23.9( .941) 25.9(1.020) 27.9(1.098) 29.9(1.177) 31.9(1.256) 33.9(1.335) 35.9(1.413) 7.95( .313) 9.95( .392) 11.95( .470) 13.95( .549) 15.95( .628) 17.95( .707) 19.95( .785) 21.95( .864) 23.95( .943) 25.95(1.022) 27.95(1.100) 29.95(1.179) 31.95(1.258) 33.95(1.337) 35.95(1.415) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 post: copper alloy, copper-undercoated, tin/lead-plated wafer: nylon 46, ul94v-0, natural (white) solder tab: brass, copper-undercoated, tin/lead-plated note: 1. the products listed above are supplied on embossed-tape. 2. contact jst for the top entry type headers with suction cap. ph connector as the color identification, the following alphabet shall be put in the underlined part. for availability, delivery and minimum order quantity, contact jst. ex. b2b-ph-sm3-oo -tb (blank)?atural (white) r?ed e?lue
26 ph connector taping specifications of sm3 type shrouded headers feeding direction (w1 +.098 - .039 [13.0(.512)dia.] w1 + 2.5 - 1.0 ) cover tape leader area carrier tape feeding direction connector loaded area 150.0 (5.906)min. tail tape (unloaded area) 40.0(1.575)min. lead tape (unloaded area) 20 vacancies min. 380 2.0(14.961 .079)dia. 2.0 0.5 (.079 .020) f 0.1 (.004) w 0.3(.012) 4.0 0.1 (.157 .004) feeding direction 1.75 0.1 (.069 .004) 2.0 0.1 (.079 .004) 1.55 0.05 (.061 .002)dia. 12.0 0.1 (.472 .004) 0.38 0.05 (.015 .002) cover tape carrier tape 4.0 0.1 (.157 .004) 2.0 0.1 (.079 .004) 12.0 0.1 (.472 .004) feeding direction 1.55 0.05 (.061 .002)dia. f 0.1 (.004) w 0.3(.012) 1.75 0.1 (.069 .004) s 0.1(.004) 0.38 0.05 (.015 .002) cover tape carrier tape f 0.1 (.004) w 0.3(.012) 4.0 0.1 (.157 .004) 1.75 0.1 (.069 .004) 2.0 0.1 (.079 .004) 12.0 0.1 (.472 .004) 0.38 0.05 (.015 .002) 1.55 0.05 (.061 .002)dia. feeding direction cover tape carrier tape 4.0 0.1 (.157 .004) 2.0 0.1 (.079 .004) 12.0 0.1 (.472 .004) feeding direction 1.55 0.05 (.061 .002)dia. f 0.1 (.004) w 0.3(.012) 1.75 0.1 (.069 .004) s 0.1(.004) 0.38 0.05 (.015 .002) carrier tape cover tape top entry type (2 to 6 circuits) top entry type (7 to 16 circuits) note: 1. specifications conform to jis c 0806. the tape width, connector loading recess square hole dimensions, etc. are determined by the number of circuits and external shape of the connector to be loaded. 2. specifications are subject to change without prior notice. 17.5( .689) 25.5(1.004) 33.5(1.319) 45.5(1.791) 57.5(2.264) 17.5( .689) 25.5(1.004) 33.5(1.319) 45.5(1.791) 57.5(2.264) 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 fsww1 16.0( .630) 24.0( .945) 32.0(1.260) 44.0(1.732) 56.0(2.205) 16.0( .630) 24.0( .945) 32.0(1.260) 44.0(1.732) 56.0(2.205) 28.4(1.118) 40.4(1.591) 52.4(2.063) 28.4(1.118) 40.4(1.591) 52.4(2.063) 7.5( .295) 11.5( .453) 14.2( .559) 20.2( .795) 26.2(1.031) 7.5( .295) 11.5( .453) 14.2( .559) 20.2( .795) 26.2(1.031) 2 to 3 4 to 6 7 to 9 10 to 14 15 to 16 2 to 3 4 to 6 7 to 9 10 to 14 15 circuits taping dimensions mm(in.) q'ty / reel reel dimensions mm(in.) top entry type side entry type side entry type (2 to 6 circuits) side entry type (7 to 15 circuits)
27 smt type pc board layout (viewed from component side) and assembly layout 1.6 0.1 (.063 .004) 1.6 0.1 (.063 .004) 2.0 0.05 (.079 .002) 1.0 (.039) 3.0 0.1 (.118 .004) 1.0 min. (.039) end face of wafer on the mating side 7.5(.295) min. max. 2.0(.079) 5.0(.197) 8.6(.339) 6.6(.260) max. 9.0(.354) min. (.039) 3.4 0.1 (.134 .004) 0.2 (.008) 1.5 0.1 (.059 .004) 1.6 0.1 (.063 .004) 2.0 0.05 (.079 .002) end face of wafer on the mating side 1.0 min. 5.5(.217) 7.6 (.299) 9.6 (.378) 1.0 (.039) 5.5 (.217) sm3 type side entry type top entry type note: 1. tolerances are non-cumulative: 0.05mm( .002" ) for all centers. 2. the dimensions above should serve as a guideline. contact jst for details. ph connector contact crimp applicator mks-l(-10) compact crimp applicator mks-ls strip-crimp applicator mks-sc with safety cover without safety cover with safety cover without safety cover with safety cover applicator for the semi-automatic press ap-k2n sph-002t-p0.5s aplmk sph002-05s aplnc sph002-05s aplmkls sph002-05s apllsnc sph002-05s aplsc sph002-05s sph-004t-p0.5s aplmk sph004-05s aplnc sph004-05s aplsc sph004-05s
|
